best selling
-
HEM Single Socket IP53 Weatherproof – 10A
IP53 rating provides weather resistance making this product suitable for outdoors.
Power: 10A
Input Voltage: AC 250V -
HEM MR16 Lamp Holder + 20cm Wire
HEM standard lamp holder for a MR16 bulb type with a 20cm wire.
Wire Length: 200mm -
HEM Photocell/ Daylight switch 6A
This light control switch is an auto daylight light sensor switch allowing adjustment of brightness.
Electronic devices are controlled to switch on or off through illumination which turns the light on at night and off in the daytime.Input Voltage: AC 220V
Max Load Current: 6A
Frequency: 50-60Hz
Ambient-light:<5-100lux -
-
56Series L1 MODULE ENCLOSURE COVER IP66
Width 95 mm
Height 95 mm
Depth 28 mm -
HEM GU10 Lamp Holder +30cm Cable
HEM standard lamp holder for a GU10 bulb type with a 30cm wire.
Wire length: 300mm -
![3 Pin Plug to Bare End [1M]](https://mew.co.nz/wp-content/uploads/2025/06/eyJidWNrZXQiOiJ3ZWItbmluamEtaW1hZ2VzIiwia2V5IjoidmVzdGFcL2ltYWdlc1wvcHJvZGltZ1wvMjY5MV8xLmpwZyIsImVkaXRzIjp7InJlc2l6ZSI6eyJ3aWR0aCI6NDgwLCJoZWlnaHQiOjQ4MCwiZml0IjoiaW5zaWRlIiwid2l0aG91dEVubGFyZ2VtZW50Ijp0-300x300.webp)
3 Pin Plug to Bare End [1M]
High quality SAA Approved 3 pin plug to bare end, 3 core 1mm cable, 10A rated. Ideal for engineers,technicians and DIY use.
Cable Size: 1mm
Color: Black
Current rate: 10A
Length: 1M -
16MM SINGLE CORE XLPE CABLE
For mains, sub-mains and sub circuits unenclosed, enclosed in conduit, buried direct or in underground ducts for buildings and industrial plants where not subject to mechanical stress. Suitable where space is at a premium and/or where conditions of overload may occur.
Conductor: Plain annealed copper
Insulation: XLPE X-90
Sheath: PVC 5V-90
Voltage: 0.6/1KV
Standards: AS/NZS 1125, AS/NZS3808 and AS/NZS 5000.1
Voltage: 90°C -
EMERGENCY LIGHTING CONTROLLER 230V
ENYA series
Timer for automatic test of emergency lights
Integrated test key
1 change over contact
Width 17.5mm
Installation designTechnical dataWs Single shot leading edge with control contact
Time ranges
Time range reversible between
10min, 30min, 60min, 90min, 2h and 3h
IP rating IP20
Tightening torque: max. 1Nm
Terminal capacity:
1 x 0.5 to 2.5mm² with/without multicore cable end
1 x 4mm² without multicore cable end
2 x 0.5 to 1.5mm² with/without multicore cable end
2 x 2.5mm² flexible without multicore cable end
5. Input circuit
Supply voltage: 230V AC
Terminals: L-N
Tolerance: -15% to +10%
Rated frequency: 48 to 63Hz
Rated consumption: 2VA (1.0W)
Duty cycle: 100%
Reset time: 500ms
Ripple and noise at DC: –
Drop out voltage: >30% of supply voltage
Overvoltage category: III (in accordance with IEC 60664-1)
Rated surge voltage: 4kV -
PDL Keystone Format Data Jack Clip Module – White
PDL 600 Series were designed and engineered locally in Christchurch, taking into account the specific needs of New Zealand and Australian homes and building.
The plastics used in 600 Series are recycleable so once no longer required, need not place a burden on our landfills.Note: we do have full range of PDL 600 series, please ring us if you need something else.
Colour: White
Vertical Installation
Length: 23mm
Depth: 15.3mm
Material: Polycarbonate -
Reem Budget 12W 850lm, IP20, 4K
REEM Budget series Ceiling / Wall LED circular lamp.
Ideal for Bathroom, Bedroom, Dining, Kitchen, Living Room.
Commercial for cloak rooms, kitchens, hallways, service areas etc.Voltage: 230V, 50/60Hz
Colour: 4000K
Dimension: 250*35mm
Lumen: 850lm
IP20
Power: 12W -
SEDEX 90Cut 10Watt Downlight LED 3CCT
SEDEX combines sleek, modern design with advanced features, making it perfect for any living or working environment.
Crafted from high grade IP44 weather resistant material, SEDEX guarantees longevity and optimal performance for years to come.
SEDEX provides exceptional energy efficiency with up to 80% energy savings which makes it a perfect fit for your home.
Not only does our SEDEX light provide impressive lighting and durability, but it also comes with warranty ensuring peace of mind and reliability.Discover the Brilliance of SEDEX and bring impressive illumination to any space!
Power : 10watt
Voltage : 220-240AC, 50Hz
CCT : 3000K, 4000K, 6000K
Cut : 90mm
Overall : 115mm
Lumens: 850lm
IP rating : IP44
CRI: >80
Dimmable
IC-F
2 YEAR WARRANTY -
TANZINI SINGLE ISOLATING SWITCH 2P 20A IP66
TANZINI IP66 Isolating switch rates at 20A, and meets AS/NZS standards. Good for isolating air condintioner, hot water cylinder, and other applicances.
-
SDocs:V0721-ISO1P20
Voltage: 250V
IP66
Current: 20A
Dimension:85x85x70 mm -
-
CHINT AC Contactor 2 x N/O 2Pole 20A
Din Mount 2P 20 amp Contactor 240V 2 x N/O
-
SURFACE MOUNT FRAME FOR PANEL LIGHT 600*1200*50
HIGH QUALITY SURFACE MOUNT FRME FOR PANEL LIGHTS
SUITS 600*1200mm PANEL LIGHTS. -
CHINT AC Contactor 4 x N/O 4Pole 25A
Din Mount 4P 25 amp Contactor 240V 4 x N/O
-
Aluminium Metal Cover for HEM/HQE OneGang Switch
Aluminium cover applicable for HEM and HQE one gang switch.
-
SDocs:V1019-WS
Size: 74W x 118H (mm)
Material: Aluminium -
-
-
TANZINI SINGLE ISOLATING SWITCH 2P 20A IP66
TANZINI IP66 Isolating switch rates at 20A, and meets AS/NZS standards. Good for isolating air condintioner, hot water cylinder, and other applicances.
-
SDocs:V0721-ISO1P20
Voltage: 250V
IP66
Current: 20A
Dimension:85x85x70 mm -
-
56Series L1 MODULE ENCLOSURE COVER IP66
Width 95 mm
Height 95 mm
Depth 28 mm -
-
3 Pin Plug to Bare End [1M]
High quality SAA Approved 3 pin plug to bare end, 3 core 1mm cable, 10A rated. Ideal for engineers,technicians and DIY use.
Cable Size: 1mm
Color: Black
Current rate: 10A
Length: 1M -
4MM 2Core GARDEN CABLE
2 Core Parallel Webbed (Figure 8) 127/.2 (4.0mmsq). P.A.C.W.
FLEXIBLE U.V resistant P.V.C insulated.
Low Voltage Cable. Not for mains connection.Conductor: 127 strands of 0.2mm Plain Annealed Copper to AS/NZS1125 drawn from Class 110A copper to AS/NZS1574.
Max. D.C. resistance at 20C: 4.63 ohms / km.Insulation: Coloured U.V Resistant P.V.C.
Parallel Webbed (Figure 8 configuration).
Nominal Diameter: 4.70 x 9.5 mm.
Nominal Wall Thickness: 1.0 mm. -
1.0MM TWIN SPEAKER CABLE – 50M/DRUM
High quality 2 core 1.0mm speaker cable. Ideal for home or mobile audio systems. The red stripe makes it easy for polarity identification.
Conductor Material: Bare Copper
Conductor Size: 17AWG / 1.0mm
Structure(mm): 2C x 32/0.20
Insulation material: Polyvinyl Chloride
Approx. Dia(mm):3.0×6.0
Pack: 50M -
![HDMI 10Gbs Slimline High Speed Cable with Ethernet [0.5M]](https://mew.co.nz/wp-content/uploads/2025/06/eyJidWNrZXQiOiJ3ZWItbmluamEtaW1hZ2VzIiwia2V5IjoidmVzdGFcL2ltYWdlc1wvcHJvZGltZ1wvMjgyM18xLmpwZyIsImVkaXRzIjp7InJlc2l6ZSI6eyJ3aWR0aCI6MzIwLCJoZWlnaHQiOjMyMCwiZml0IjoiaW5zaWRlIiwid2l0aG91dEVubGFyZ2VtZW50Ijp0-300x290.webp)
HDMI 10Gbs Slimline High Speed Cable with Ethernet [0.5M]
High quality slimline high speed HDMI cable to support continuing market requirements for video and audio system.
2160p 4K2K @24/30Hz
8 audio channels
8bit colour depth
Supports CEC, 3D, ARC, Ethernet
Length: 0.5m
Colour: Black -
Cat6 UTP Blue Patch Lead
The Cat6 UTP patch leads conform to the TIA/
EIA-568-B specifi cation. Patch leads are wired
to the T568A pinout specifi cation. They are
individually channel tested and are made with tangle free slimline injection molded boots.Features:
• Produced by an ISO9001 and ISO14001
certifi ed manufacturer
• 100% tested and channel certified by 3P, UL and ETL
Colour: Blue
Length: 0.3m
Frequency: 550MHz -
4MM CONDUIT WIRE – GREEN/YELLOW
Single core conduit wire with 0.6/1KV V-90 insulation.
PVC sheathed complies with AS/NZS 5000.2 standards which was manufactured in accordance with PVC best practice guidelines.
It is suitable for fixed wiring installation for power circuits in domestic, commercial and industrial situations.Conductor material: Copper
Outer sheath: PVC
Insulation: PVC
Cores x Area (mm2): 1 x 4.0
Rated Voltage Uo/U: 0.6/1 KV
Max. conductor temperature in service: 75°C
Nom Diameter: 4.7 mm
Color: Green/yellow -
1 X 1.5mm High Performance Flexible Appliance / Marine Wire – Green/Yellow
Applications:
Power
Flexible thermal insulated wire suitable for switchboard wiring, motors and transformers.
Marine
Tinned copper conductors for boat wiring and other marine applications.
Audio
Amplifiers and audio equipment where oxygen-free copper wire is required.It features:
Tinned fine stranded copper conductor
UV stabilised
Flame retardant
Oil and chemical resistant (refer to Chemical Rating Chart)
No. of Cores x Size (mm): 1 x 1.5
Approx Stranding (No. of wires x mm): 30/0.25
Approx. Overall Diameter (mm): 3.4 -
PRYSMIAN 1MM 2C+E TPS FLAT
Two core plus earth flat cable with 450/750V V-90 insulation.
PVC sheathed complies with AS/NZS 5000.2 standards which was manufactured in accordance with PVC best practice guidelines.
Includes 90°C copper conductors.
It is suitable for fixed wiring installation for power circuits in domestic, commercial and industrial situations.Conductor material: Copper
Outer sheath: PVC
Insulation: PVC
Cores x Area (mm2): 2 x 1.0 + 1.0 E
Rated Voltage Uo/U: 450/750 V
Max. conductor temperature in service: 75°C
Earth selection cross: 1.0 mm²
Nom Diameter: 4.0 x 8.6 mmSubject to stock available.
-
95MM 1 CORE ALUMINIUM CABLE
This cable may be buried directly in the ground, or may be installed in ducts buried in the ground. Used for Indoors, cable ducts, outdoors and buried in the ground, for power stations, industry and switchgear as well as for urban supply networks, if mechanical damage is unlikely. XLPE insulation material has better mechanical, electrical, chemical and durability characteristics than PVC.
Conformance: AS/NZS 5000.1
Core colour: Natural
Number of Core: 1
Conductor: Al 1350 AS/NZS 2848.1
Conductor Size: 95mm
Insulation: XLPE X-90 AS/NZS 3808
Sheath: PVC 5V-90 Black AS/NZS 3808
Test voltage: 3.5kV/5min
Temperature range: -40 to 90C -
DYNMAICS ALARM CABLE 100M, 4C, 022MM, BARE COPPER
Dynamix C-S4C100-22 100M 4C 0.22mm Bare Copper Security Cable. Supplied on Plastic Reel
0.22MM
4 CORE
100 MTR / DRUM -
16MM SINGLE CORE XLPE CABLE
For mains, sub-mains and sub circuits unenclosed, enclosed in conduit, buried direct or in underground ducts for buildings and industrial plants where not subject to mechanical stress. Suitable where space is at a premium and/or where conditions of overload may occur.
Conductor: Plain annealed copper
Insulation: XLPE X-90
Sheath: PVC 5V-90
Voltage: 0.6/1KV
Standards: AS/NZS 1125, AS/NZS3808 and AS/NZS 5000.1
Voltage: 90°C -
2 x 4mm2 Solar Cable DC 1.5kV EN5061/IEC62930 100METER
2 X 52/.3 (4mmsq). Tinned Copper Wire, XLPO Insulated & XLPO.
Sheathed in Twin format.
Certified to EN50618/IEC62930. TUV
1.5kV dc -40c to 120c.Construction
Conductor: 52 strands of 0.3mm nom. TINNED Annealed Copper to AS/NZS 1125 Class 5.
Max. D.C. resistance at 20C: 5.09 ohms / km.Insulation: XLPO.
Nominal Wall Thickness: 0.60 mm.Core Colours:
1. Black
2. RedSheath: Black with red polarity stripe on side of red core.
XLPO Single Double Insulated (TWIN) configuration.
Nominal Dimensions: 5.5 x 11.4 mm
Nominal Wall Thickness: 0.6 mmIdentification: Printed on sheath in contrasting colour ¨C HFXT2520- XLPO insulated TUV 2pfG 1169 2 x 4MM2 0.9/1.5kV DC UV STABLE DC USE ONLY ¨C DO NOT DISCONNECT UNDER LOAD ¨C 001M >I<
-
Weatherproof European Junction Box 85×85
Tanzini surface-mounted, waterproof sealed plastic electrical enclosure/ Junction box with anti-corrosion performance, which can protect your instruments even under the adverse environment.
Dimention: 85WX85HX50D mm
IP66
5way terminals included -
JUNCTION BOX 77*77*54MM IP55
All products comply with AS/NZS standard.
Dimension: 77x77x54 mm
IP55
For use indoors and outdoors -
COPPER LINKS 16MM 63A-2 HOLE
Good quality copper linke which comply with AS/NZS standards.
Dimention: 45x18mm -
TANZINI SURFACE MOUNT 8 WAY SWITCH BOARDIP65
Tanzini switchboards comply with AS/NZS standard and waterproof.
This surface mount switchboard is applicable with a range of our circuit breakers and including RCD bars , earth bar , neutral bar and busbar.Plenty of different sizes distribution board are available.
-
SDocs:V0421-SWBX
Mounting method: Surface
Dimention: 210x210x100mm
IP rating: IP65
Main earth bar: 1
Main neutral bar: 1
Bus bar: 1 -
-
TANZINI SURFACE MOUNT 4 WAY SWITCH BOARDIP65
Tanzini switchboards comply with AS/NZS standard and waterproof.
This surface mount switchboard is applicable with a range of our circuit breakers and including RCD bars , earth bar , neutral bar and busbar.Plenty of different sizes distribution board are available.
-
SDocs:V0421-SWBX
Mounting method: Surface
Dimention: 140x210x100mm
IP rating: IP65
Main earth bar: 1
Main neutral bar: 1
Bus bar: 1 -
-
TANZINI DATABOARD 14″ WALL MOUNT
SPECIFICATIONS:
BASE SIZE: 273 X 355 mm
FRAME SIZE: 315 X 385 mmADJUSTABLE INSULATION BOARD (150 X 120 MM) X 1
SMART MATRIX HOLES FOR DEVICES MOUNTING
EASY CABLE ACCESS
SUPPLIED WITH LOCKABLE DOOR AND 2 KEYS
COMPREHENSIVE HOLE FOR INSTALLING POWER SOCKETS WHICH SUITS MOST BRANDS IN NZ -
Recessed AV Wall Box
Features:
-Socket outlet opening suitable for AS/NZS sockets.
-Two options of side outlets.
-Optional brush outlet easy for cable entry
-Optional keystones easy for connector installation
-Suitable for 70mm or 90mm wall cavities
-Suitable for plaster walls onlyCut-out size: 166x100mm
Product size: 180x145x55mm -
TANZINI Surface Mount 6 Way DistributionBoard
Tanzini switchboards comply with AS/NZS standard.
This surface mount switchboard is applicable with a range of our circuit breakers and including RCD bars , earth bar , neutral bar and busbar.Plenty of different sizes distribution board are available.
-
SDocs:V0421-SWBX
Mounting method: Surface
Dimention: 147x200x95mm
Main earth bar: 1
Main neutral bar: 1
Bus bar: 1
RCD bar:1
Indoor use only -
-
TANZINI Surface Mount 4 Way DistributionBoard
Tanzini switchboards comply with AS/NZS standard.
This surface mount switchboard is applicable with a range of our circuit breakers and including RCD bars , earth bar , neutral bar and busbar.Plenty of different sizes distribution board are available.
-
SDocs:V0421-SWBX
Mounting method: Surface
Dimention: 112x200x95mm
Main earth bar: 1
Main neutral bar: 1
Bus bar: 1
Indoor use only -
-
TANZINI Flush Mount 6 Way Distribution Board
Tanzini switchboards comply with AS/NZS standard.
This surface mount switchboard is applicable with a range of our circuit breakers and including RCD bars , earth bar , neutral bar and busbar.Plenty of different sizes distribution board are available.
Mounting method: Flush
Overall: 172W x 221H x 90D
Main earth bar: 1
Main neutral bar: 1
Bus bar: 1
Indoor use onlyF -
TANZINI Flush Mount 4 Way Distribution Board
Tanzini switchboards comply with AS/NZS standard.
This surface mount switchboard is applicable with a range of our circuit breakers and including RCD bars , earth bar , neutral bar and busbar.Plenty of different sizes distribution board are available.
Mounting method: Flush
Overall Dimention: 136x221x90mm
Main earth bar: 1
Main neutral bar: 1
Bus bar: 1
Indoor use only -
HEM MR16 Lamp Holder + 20cm Wire
HEM standard lamp holder for a MR16 bulb type with a 20cm wire.
Wire Length: 200mm -
-
HEM Photocell/ Daylight switch 6A
This light control switch is an auto daylight light sensor switch allowing adjustment of brightness.
Electronic devices are controlled to switch on or off through illumination which turns the light on at night and off in the daytime.Input Voltage: AC 220V
Max Load Current: 6A
Frequency: 50-60Hz
Ambient-light:<5-100lux
